835/836 UL Operator Control Board

835/836 Control Board Parts Identification

 

	ACTUATOR CONNECTOR
	Board Actuator Cable Function Pin 1 Orange Open Limit Pin 2 White Close Limit Pin 3 Black Motor (positive on open, negative on close) Pin 4 Red Motor (negative on open, positive on close) Pin 5 Green Common for both limit switches Pin 6 Yellow Feedback from intelligent actuator (816E/816EX) Pin 7 Black Battery Negative Pin 8 Red Battery Positive
	EMERGENCY BYPASS
	Applies battery voltage directly to motor to open gate if control board fails. User must unplug before gate opens to maximum travel or 15 amp fuse will open. Fuse should be checked before returning gate to service.
	REMOTE OUTPUTS
	12V Supplied battery voltage SLV Slave Operator Indicator (indicates slave side of gate is closed) +1 2V when on closed limit. Ground when off of closed limit. MAS Master Operator Indicator (indicates master side of gate is closed) +1 2V when on closed limit. Ground when off of closed limit SND Battery supplied ground SIREN Conned to siren + (optional) +1 2V when gates) are running or in hard shutdown SND Battery supplied ground LOCK Connect to lock + (optional) Magnetic or Solenoid type locks (Dip Switch #6 Selectable)
	GATELINK CONNECTOR
	Connects control board to a computer using GateLink software. This software can monitor and diagnose the functions of the microprocessor. Ask your salesperson about this feature.
	ADJUSTMENTS
	TIMER TO CLOSE Adjusts time before gate automatically closes 1-60 seconds, DUAL GATE DELAY (836 only) Adjusts delay between master and save operation 0-4  seconds. (for use with magnetic and mechanical locks or stop tabs) CURRENT SENSITIVITY Increases or decreases the Auto Reverse sensitivity
	PUSH BUTTONS
	LED ENABLE When depressed, activates LEDs for 15 minutes to assist in installation and troubleshooting.
	RESET Resets the microprocessor. Returns processor to last known state.
	JUMPERS
	STOP CIRCUIT JUMPER When the STOP CIRCUIT JUMPER is connected, the gate will operate normally.
	STOP CIRCUIT JUMPER When a 3-button station is connected to the board, the STOP CIRCUIT JUMPER must be removed.

  PROGRAM SWITCHES

 

	OFF	ON
1 TIMER TO CLOSE	Gate does not automatically close.	Gate automatically closes
2 TIMER TO CLOSE OPT.	Gate automatically closes from any position after opening.	Gate automatically closes only when completely open (open limit engaged)
3 SLAVE DISABLE	Enables slave side (dual gate use).	Disables slave side. (single gate use)
4 SIREN DELAY	Siren (optional) starts when gate moves	Siren (optional) starts 3 seconds before gate moves.
5 'STOP' CIRCUIT ENABLE	Must hold down open or close buttons to move gate. Gate stops when button released.	Normal operation Momentary open or close runs gate to limit.
6 LOCK TYPE	For 12V mechanical (solenoid) locks. (+12V for 4 seconds an open cycle)	For 12V magnetic looks (+12V when on close limit)
7 COAST ENABLE	Gate will brake when at Open or Close limit	Gate will coast (minimally) when it reaches limits.
8 FREE EXIT OPT.	A free exit input will open gate from closed position or after a close cycle only.	A free exit input will open gate from any position after an open or close cycle
9 LEARN MODE	Normal Operation	Control board determines reverse current sensitivity and when to start slowing down opening and closing (used during installation),
10 SMART ACT.	Used for 416E & 416EX actuators, slide gates, or when slow down feature is not desired	Used for 816E & 816EX actuators (soft start & stop).

OPTIONAL DEVICE INPUTS
 

	GND Supplied Battery Ground INP Activate Gate (Push button activation when momentarily shorted to ground) 12V Supplied Battery Voltage (Protectecf with 3 Amp fuse)
	GND Supplied Battery Ground INP Activate Gate (Push button activation when momentarily shorted to ground) 12V Supplied Battery Voltage (Protected with 3 Amp fuse)
	EDGE Reverse edge input. When grounded, will stop and reverse gate if closing, resets close timer if gate is open. EDGE Reverse edge input. When grounded, will stop and reverse gate If closing resets close timer if gate is open GND Supplied Battery Ground GND Supplied Battery Ground STOP Stop input from a 3 button station (must remove STOP CIRCUIT JUMPER) Normally closed CLOSE Close input from a 3 button station (see program switch #5 for options) OPEN Open input from a 3 button station (see program switch #5 for options)
	GND Supplied Battery Ground GND Supplied Battery Ground FREE EXIT Opens gate if closed, stops and reverses gate if closing, resets close timer if gate is open GND Supplied Battery Ground SHADOW Resets close timer when gate is open (also referred to as under gate loop) GND Supplied Battery Ground SAFETY Resets close timer if gate is open, stops and reverses if gate is closing. (Does not open a closed gate)
	GND Supplied Battery Ground FIRE When grounded, opens gate and holds gate open until released. UL When grounded, opens gate and holds gate open until released. Clears 'Hard Shutdown" mode of UL software.
	GND Supplied Battery Ground INP Activate Gate (Push button activation when momentarily shorted to ground) 12V Supplied Battery Voltage (Protected with 3 Amp fuse)

  911 Siren

The 911 Siren is included with all Apollo UL Gate Operators.

Mount siren in an area that will produce maximum performance (additional wire may be required).
Connect the red wire to the SIREN connector on the Remote Monitor Output Connector block.
Connect the black wire to the GND connector on the Remote Monitor Output Connector block.

Set Program Switch # 4 as preferred:

ON - Upon activation, Siren will start for 5 seconds before gate(s) begin moving.
OFF - Siren and gate(s) start immediately upon activation.
 

E-mail for more information

Revised: March 05, 2008 .
contact webmaster for web site problems